准比例谐振控制算法在三相逆变电源中的应用研究

非线性负载会在三相车载逆变电源系统中引入谐波,损伤用电设备。为了降低逆变电源输出电压谐波含量,文章研究了基于准比例谐振控制算法的谐波抑制方法 ,主要抑制电源输出的5次和7次谐波。通过仿真模型和实物试验,测试了传统瞬时控制方法和准比例谐振控制方法的差别。结果表明,准比例谐振控制方法既能消除输出电压中的特定次谐波,又可满足系统动态响应性能和稳态精度要求,具有良好的谐波抑制效果。     

On the importance of mooring system parametrisation for accurate floating structure designs

This paper analyses the importance of mooring design parametrisation on the dynamic behaviour of mooring loads. An exhaustive sensitivity analysis is performed to evaluate the variability of mooring loads because of inaccuracies in the definition of model inputs, including physical and numerical parameters. Results show a relevant dependence on the length and significance in other parameters, such as the weight together with the hydrodynamic equivalent diameter and the drag forces. An inaccuracy below 1% in the mooring reference length can generate loads of up to twice the design, and an incorrect definition of the weight or the drag coefficient in the mooring design can lead to a design load variability of up to 30%. Stiffness plays a crucial role in snap events, reaching load differences of 19% depending on the stiffness selected.This research is based on a set of numerical models capable of predicting the mooring system response. A dynamic numerical model with two schemes of resolution is implemented and calibrated according to an experimental test campaign. Other sources of results provided by a quasi-static model and commercial software, Sesam (DNV-GL), are incorporated. In general, the dynamic numerical models show a good accuracy with an experimental database composed by a set of 2D prescribed movement tests at the fairlead of the mooring system.     

水深对船舶运动和波浪载荷的影响

本文利用简单Green函数法计算二维水动力，特切片法用于有限深水中船舶运动和波载的计算。对实船试算了迎浪航行时几种不同航速和水深的组合，计算结果（垂荡和纵摇响应、舯弯矩和钟前1／4船长处剪力）表明水深的显著影响。水深变浅，垂荡和纵摇响应峰值变小，弯矩和剪力变大，航速越大水深的影响越显著。     

冲击荷载下CRTSⅡ型板式无砟轨道结构振动与噪声的关联性研究

为揭示冲击荷载作用下无砟轨道结构振动和噪声的内在关联性,采用1∶1足尺模型对CRTSⅡ型板式无砟轨道结构进行多组冲击振动试验。通过在板式无砟轨道不同方向、不同位置的锤击,获得钢轨轨顶、轨腰、轨底各个位置的加速度及声强声压数据,采用快速傅里叶变换(FFT)获得了振动和噪声的频谱图,并进行频域特性对比分析,研究振动和噪声的内在关联性。结果表明:侧向冲击荷载下,轨顶轨腰处声强主要与侧向振动有关,频谱图峰值对应良好;垂向冲击荷载下,0~1 500 Hz区段的声强主要受垂向振动影响。     

小方型系数船舶的船体波浪载荷综合研究

从船级社规范对于不符合主尺度比要求的船舶船体梁波浪载荷的规定出发,采用理论预报和船模试验2种综合方式,进行了小于0.6方型系数、高航速、高海况目标船的波浪载荷研究.从规范对波浪载荷的线性理论预报值进行的非线性修正,修正后中拱和中垂波浪弯矩绝对值之和与线性理论预报极值全幅值相等出发,阐述所研究船特殊主尺度比下的模型试验结果、三维非线性水弹性理论预报结果显示出的波浪载荷非线性行为;同时综合模型试验与理论预报的共同规律,研究不同波高、航速、浪向等非常规船型船体波浪载荷的强非线性行为,从而认为规范基于的线性理论预报值进行非线性修正的统一规定太过笼统,进而建议规范对波浪载荷的非线性修正予以进一步的明确区分和规定.     

Comparing different contour methods with response-based methods for extreme ship response analysis

Environmental contours are often applied in probabilistic structural reliability analysis to identify extreme environmental conditions that may give rise to extreme loads and responses. They facilitate approximate long term analysis of critical structural responses in situations where computationally heavy and time-consuming response calculations makes full long-term analysis infeasible. The environmental contour method identifies extreme environmental conditions that are expected to give rise to extreme structural response of marine structures. The extreme responses can then be estimated by performing response calculations for environmental conditions along the contours.Response-based analysis is an alternative, where extreme value analysis is performed on the actual response rather than on the environmental conditions. For complex structures, this is often not practical due to computationally heavy response calculations. However, by establishing statistical emulators of the response, using machine learning techniques, one may obtain long time-series of the structural response and use this to estimate extreme responses.In this paper, various contour methods will be compared to response-based estimation of extreme vertical bending moment for a tanker. A response emulator based on Gaussian processes regression with adaptive sampling has been established based on response calculations from a hydrodynamic model. Long time-series of sea-state parameters such as significant wave height and wave period are used to construct N-year environmental contours and the extreme N-year response is estimated from numerical calculations for identified sea states. At the same time, the response emulator is applied on the time series to provide long time-series of structural response, in this case vertical bending moment of a tanker. Extreme value analysis is then performed directly on the responses to estimate the N-year extreme response. The results from either method will then be compared, and it is possible to evaluate the accuracy of the environmental contour method in estimating the response. Moreover, different contour methods will be compared.     

计及叶片载荷的双机对转式海流发电机系泊系统动力分析

本文设计了一种新型的双机对转式海流发电机并对其系泊系统与叶片载荷和直径关系进行模拟分析。首先将单机式海流发电机与已有研究进行对比验证其可靠性，然后在不改变系泊方式的前提下，设计出双机式结构，并通过分析机身位移和旋转比较两种系统的稳定性。为考虑叶片载荷对系泊系统影响，在Orcaflex中对不同精细程度的叶片进行建模，分别对比单一翼型/三翼型/九翼型的数值模拟结果。接着使用M-BEMT软件优化后的翼型参数，对比使用原始升阻力系数的三翼型发电机的模拟结果，同时将使用不同直径叶片的发电机系统进行对比，说明双机式发电机的稳定性更优，对海流发电机及其系泊系统的设计提供重要参考价值。     

复杂载荷下裂纹SIF计算的子模型技术

对船舶与海洋工程结构物进行疲劳评估,首先要通过子模型技术解决复杂应力场中裂纹应力强度因子(SIF)的计算问题。针对子模型技术实现过程繁杂且效率较低的问题,分别提出"逐周分层法","转换矩阵法"及"映射划分法"并基于VBA及APDL语言编写插件MPCarrangerV1.0,FEMcoortransferV1.0及CrackmapperV1.0,解决从Patran整体有限元模型到Ansys子模型时壳体单元间MPC创建低效、不同坐标系间节点位置转换困难及裂纹自由划分的局限性问题。基于DNV及ABS相关规范,以某B型LNG燃料舱的疲劳热点为例,对改进的子模型技术进行验证,结果表明经改进的子模型技术可成功施加合理边界条件并实现SIF的求解,可为子模型技术快速实现复杂载荷下裂纹SIF的准确计算提供参考。     

内河船舶波浪载荷研究

利用内河波浪散布图和修订波浪谱对内河系列船舶进行了波浪载荷的计算预报,首次分析了内河船舶波浪载荷的规律和特点,并与俄罗斯内河登记局(RRR)和法国-德国船级社(B-G)的内河规范载荷对应的等效模数要求进行了比较分析。结合实船测试结果表明：波浪载荷变化规律与国外同类规范一致,预报波浪载荷水平与测试结果及国外同类规范要求相当。内河船舶波浪载荷预报应考虑航速和水深的影响,载荷预报结果可以作为制定内河波浪载荷公式的基础。     

基于准动态法的穿梭油轮多点系泊分析

边际油田一般使用穿梭油轮进行原油运输.为减少穿梭油轮系泊的施工成本和难度,提出一种简单的系泊方式,即船尾用缆绳直接系泊于平台上,船首用锚链系泊于海底.基于准动态分析方法,设置风浪流不同方向组合、不同抛锚角以及不同的环境载荷,计算该系泊系统的受力特性和作业的限制工况.结果表明:该系泊系统在30°抛锚角下对环境力耐受程度最好;在波浪方向一定时,横流对系泊系统的影响比其他情况大,考虑系泊安全时进行风浪流不同方向组合是非常必要的;在环境条件已知且良好时,该系泊系统具有良好的适用性和经济性.